Rendering of a digital model done for B&B Props. B&B cut out the body of the model using their robotic mill while 3D printing deck furniture and small details.
The finished model that B&B Props created using this digital model can be seen in the Vehicles folder. As always they made it look fantastic.
Digital model of Angry Vandal figure modeled and printed for Carmelo Sigona.
Angry Vandal close up.
Angry Vandal parts still on the print bed in their wax support.
Angry Vandal figure assembled.
This 1959 Cadillac was modeled for B&B Props. The model was cut out by their robotic mill using the digital model as a base for the mills programing.
1959 Cadillac after being cut out and assembled at B&B Props. The prop was painted and given working headlights and spinning wheels. It was built for an off Broadway production of The Flamingo Kid.
1959 Cadillac in all it's glory.
This Ford Falcon was modeled for B&B Props. The model was cut out by their robotic mill using the digital model as a base for the mills programing.
Ford Falcon after being cut out on B&B's robotic mill. The model was cut out using their robotic mill and then painted and given working headlights and spinning wheels. It was built for an off Broadway production of The Flamingo Kid.
The finished Ford Falcon.
This Edsel front end was modeled for B&B Props. The model was cut out by their robotic mill using the digital model as a base for the mills programing.
The milling process of the Edsel.
The Edsel after being milled and hand finished by B&B Props.
The Edsel after being milled and hand finished by B&B Props.
The lights and paint bring the Edsel to life.
This Ferrari 250 GT was modeled for B&B Props. The model was cut out by their robotic mill using the digital model as a base for the mills programing.
The Ferrari's milling process.
The Ferrari GT 250 after being milled and hand finished by B&B Props.
Left and right door pulls 15" in length. Printed for a leading architectural hardware firm to be molded and cast in bronze.
Side view of 15"door pulls.
Candle holder printed for a leading architectural hardware firm for molding to be cast in bronze.
Model of door/drawer pull. Modeled in pieces to facilitate casting in multiple materials.
Assembled test print of door/drawer pull.
Printed door/drawer pull broken down into separate parts.
Printed door/drawer pull broken down into separate parts.
Section of a drone prop Modeled for and printed by B&B Props.
Sections of the drone model assembled. The top and bottom would be laser cut from acrylic.
Inhaler modeled for B&B Props.
B&B would later add motors and propellers from an actual drone to the model.
Drone modeled for B&G Props. The blue sections were modeled as separate pieces so they could be printed in clear resin to simulate lenses.
Hand held VR remote modeled for B&B Props.
Exploded view of the VR remote. The final model that B&B Props produced would be made with a soft rubber ball in the center necessitating access to the interior of the the model.
Bow knob modeled for S.A. Baxter Architectual Hardware.
Ceramic shell mold of bow knobs to be cast in bronze.
Bronze castings of Bow knob. (Cast at S.A. Baxter)
Bronze castings finished in white lacquer.
Bow knob as it appeared in the Kips Bay Decorator Show House.
Digital model of Daniel's Ford (Foreshortened to fit on stage) for the Karate Kid
Another great job bringing my model to life by B&B Props.
Digital model of the Peugeot (Foreshortened to fit on stage) for the Karate Kid
The Karate Kid Peugeot in the B&B Props studio.
The Family Truckster from National Lampoons "Vacation"
Hawk head coin for Albersland studio.
Bear head coin for Albersland studio.
Lion head coin for Albersland studio.
Tiger head coin for Albersland studio.
Wolf head coin for Albersland studio.
gLike
Digital Models and 3D prints.